Linux 네트워크 연결 속도 확인
2014.08.21 14:44
현재 연결된 리눅스의 링크 속도를 궁금할때
mii-tool 과 ethtool 명령어로 확인이 가능하다.
mii-tool -v 엔터
eth0: negotiated 100baseTx-FD, link ok
product info: vendor 00:50:43, model 2 rev 3
basic mode: autonegotiation enabled
basic status: autonegotiation complete, link ok
capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
eth1: no link
product info: Intel 82555 rev 4
basic mode: autonegotiation enabled
basic status: no link
capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
하지만 mii-tool 은 100Mbps 까지만 확인이 된다.
동일 장비에서 ethtool 로 확인한 결과는 아래와 같다.
ethtool eth0 엔터
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7)
Link detected: yes
댓글 0
번호 | 제목 | 글쓴이 | 날짜 | 조회 수 |
---|---|---|---|---|
13 | 우분투 18.04 Home Assistant 설치 [2] | Kim | 2018.12.09 | 1254 |
12 | HylaFax on CentOS Install | Kim | 2014.11.19 | 53782 |
11 | 웹페이지 로딩 비교 사이트 | Kim | 2014.08.22 | 5634 |
10 | 64bit linux에 php with mysql시 다음 에러 해결 방법 | Kim | 2014.08.21 | 5343 |
9 | 서버점검목록 1탄 | Kim | 2014.08.21 | 4653 |
8 | 리눅스에서 하드디스크 추가로달고 마운트하기 | Kim | 2014.08.21 | 17279 |
7 | 리눅스 하드디스크 배드 블럭 점검 badblocks | Kim | 2014.08.21 | 6428 |
» | 네트워크 연결 속도 확인 | Kim | 2014.08.21 | 5370 |
5 | ip_conntrack: table full, dropping packet | Kim | 2014.08.21 | 5095 |
4 | HOSTNAME | Kim | 2014.08.21 | 4925 |
3 | 서버 리눅스 핑막기 | Kim | 2014.08.21 | 5196 |
2 | 네트워크 재시작 | Kim | 2014.08.21 | 4988 |
1 | Bad Sector 확인 | Kim | 2014.08.21 | 5396 |